1 / 1
Model No. : | FRX-DM-005 |
---|
Product description
LED Driver | Dimmable Using |
---|---|
Power | 8A,DC12V-48V |
Life | 30000Hours |
Voltage | 48V |
IP | IP65 |
Dimmable | Yes |
FRX-DM-005:led dimming driver
The product specification
The power input:DC12-24V
Transmission rate:-
The driver output:<8A
The light gray level:256
Control channels:1CH
Remote control:-
Output the maximum power:180W
Protection grade:IP40
Control mode:0/1-10V
active&passive Gross product:220g
Control interface consumption:<0.6Ma
packing:1*50(L365*W345*H195mm)
output frequency:500HZ
size:160mm*47mm*22mm
Product features
◆Single channel constant voltage output dimming control, maximum driving ability 8A.
◆No flicker, analog voltage DC 0/1-10V dimming and passive 0/1-10V dimming general,can with large family control system from structure dimmer.
◆ High frequency PWM drive output, can be used to higher occasions such as photographic studio, LED output more exquisite and smooth, no flicker.
◆Perfect dimming curve, the existing traditional 0/1-10V dimmer products! On the vision more than 70% brightness, then after regulation basic see LED brightness is still in change, this product in the design through the chip decoding simulation value, the breakthrough dimming of straight proportion acquisition, redefine a dimming curve value,do not jitter at low-end, high-end in more than 95% of the brightness value still see the
obvious change.
◆Products have self-test function, in the absence of signal input, brightness to the maximum output, can through the input end short circuit test product is in work, input end short circuit brightness will gradually dark to minimum value. Open while maintaining maximum brightness output.
Product operation
◆First way is selecting switch panel to dimming (normally open panel switch mode), must put the
interface (SWITCH DIM) short circuit.
◆ When short time press the switch is opening or closing state, the booting has memory and
brightness delay light or dark function. Can realize switch light once light up or down instant.
◆When press the switch with a long time,the brightness plus or minus state, long press process
then stop, and in 2 seconds again continue long press, so it will keep at the last time brightness state, if is over 2 seconds long press again, then brightness will be instead state control (example: the current light state is added brightness, when adjust to 50% brightness stop, if in 2 seconds long press again,then the brightness from 50% to continue upward, or it will down from 50% brightness).
◆The second way, choose active 0/1-10 v or passive signal control, it is necessary to put the line to jumper(SWITCH DIM line break down), according to the product connection diagram, adjust the 0/1-10 v dimmer SWITCH, so as to change the output of the controller, until get the satisfactory of LED output luminance.
◆In the second way,when the 【Analog IN 】port breaking, controller all light output; When the
Update 2012-10-22 Page 3 of 3 DM9103-V1.1
【 Analog IN 】 port two terminals short circuit, the output shut down.
Payment Terms | T/T, L/C, Others |
---|---|
Minimum Order | 50pcs |
Lead Time / Delivery Time | 3 Day(s) |
Sample Available | YES |
Delivery Details | Sample Order: 100% T/T, Bulk Order: 30% In advance via T/T & balance before shipment |
FOB Port | Ningbo |
Loading Info | By express,by air and by sea |
Packing Info | White box for every pcs driver,big carton for total white boxes,100pcs/carton |
Target Market(s) | Eastern Europe, Hong Kong/ Macao/ Taiwan, Middle East, North America, Northern Europe, Oceania, Central & Southern Asia, Western & Southern Europe |
Send your inquiry to this supplier