Product Description Automatic Chemical Dosing System Equipment For Waste Water Treatment Plant(WWTP Plant)/Flocculant PAM Dosing Machine PY series three cavate automatic dosing device is a kind of automatic continuous flocculant dosing system, prepararion solution range is 0-5000L/h, concentration is 0.15-0.3%. Dry powder flocculant enter into instant vessel from screw propeller internal , and premix with cleaning water, moist material enter into preparation tank to make preparation; in preparation process, the inflow water must be relative stable under the flowmeter observe, thus guarantee whole process, preparation solution concentration invariant. The preparation solution enter into storage tank from configuration tank, when storage tank liquid level high, the preparation process automatic stop, Chemical dosing process continue, when solution drop to center liquid level, automatic start dosing process again. Preparation tank and cure tank all equipped with mixer, fully guarantee flocculant dilution and curing. In addition, when storage tank solution not enough, it will touch the below liquid level alarming system, the whole system will stop and alarm, this system has the characteristic of high automatic degree,stable performance,work reliable,easy operation etc.
Full automatic powder dosing system technical principle Automatic dosing system is an intelligent, automatic, continuous integration of dry powder dissolved and drug delivery device. This device consists of water supply system, dissolve powder dosing system, curing system, automatic control system. This device is powder medicament automatic continuous preparation and dosing system. dry powder chemical from hopper bottom of screw propeller into premixed premixed with clear water, by wet material into the dispensing slot to dilution mixing, concentration of production according to the requirements of customers; Preparation solutions from the preparation tank into the storage tank again after the slaking tank, when the storage tank level high, preparation process automatically stop, when the solution down to low level, automatic startup process. Preparation tank and slaking tank are set blender, fully guarantee of dilution and maturation. Preparation flow and concentration can be adjusted by adjusting the feed water flow rate and screw shaft speed to determine.
constitute * water supply system* dry powder dosing system * powder premix system * dehumidifying drying system * integration three tank combination casing * mixing system * automatic control and detection system
feature with high degree of automation, system controlled by PLC, operation on the interface and display units operating state, with intuitive man-machine interface, simple and convenient operation.
system stable and reliable, when has fault related equipment will automatically stop as required Adopting spiral feeder dosing powder, speed closed-loop control, ensure uniform feeding, scattered, precision within 1%
Under prescribed conditions of production and continuous cast liquid, the mixture solution of ripening time guarantee in 2 hours. The mixture concentration was 0.05% - 0.05%; Tank body adopt SS304,PP material etc.
Operating system adopts three tank overflow solution, has simple structure, small volume, convenient installation. Apply continuous dissolution and continuous dosing medicament environment.
The mixer adopts special design of multistage blade structure
Premixed accelerate the hydration of powder, can adjust the flow conditions.
specification
Capacity | 1000 ltr/hour |
Tank body size | 2.0x1.0x1.0m |
Dry powder tank | 100L |
Solution strength | 0.05-0.50 % |
Mixer | BLD-0.55,SS304 blade |
Powder conveyor | 2kg/h |
Material level switch | impeding level probe |
Damp heater | DN42 |
Feeder | 0.37kw |
Power | 380v, 3 phases, 50 Hz or customized |
Volume of the dosing tank | 50 lt |
Availability of powder in the tank | Visual control |
Tank body Material | PP |
Electric control cabinet | PLC,CHINT |
Dosing device rack | 10# U-steel |
Dosing metering pump | 500L/h,0.75kw,2 set |
Remark: contain material level meter, liquid level detection device, solenoid valve , mixing device ,main body, dry powder t |
Packaging & Shipping Our Services
Company Information
FAQ [Q]How to buy your idea products? [A]You can provide us your water sources, water quality, flow rate and ground area (contact us for more details). [Q]What is your payment terms? [A]TT and L/C are acceptable and TT will be more appreciated.30% deposit in advance and balance before loading. [Q]What is the delivery time? [A] It depends on order quantities. Generally speaking, the delivery time will be within 4 to 6 weeks. [Q]How to pack the products? [A]We use standard package. If you have special package requirements, we will pack as required, but the fees will be paid by customers. [Q]How to keep your equipments from corrosion? [A]We use the world-famous paint, like SigmaCoatings,PainBow,etc. What's more, we paint strictly according to the standard process. [Q]How do you manufacture your equipment ? [A]Our machining technology includes laser/plasma cutting, automatic welding,CNC cutting and bending. [Q] How to install after the equipments arriving destination? [A] We will provide detailed illustrations to you. If it is necessary, we will send technicians to help you.