Video
1 / 1
Model No. : | 1800E |
---|---|
Brand Name : | Ultra-lite |
Kind of power : | Electric |
Chungli, Taoyuan, China Taiwan
Product description
Product Description& Fields of Application
The Ultra-lite 1800E DUAL is a high-performance LED Curing Light intended for polymerization of light cured dental materials by dental professionals. The Ultra-lite 1000E DUAL Curing Light incorporates two types of LEDs to achieve broad wavelength with range of 390 to 480nm output to polymerize virtually all light-activated materials in the market and a high power mode to produce super-fast curing effect. The relevant range both for camphorquinone (CQ) and phenyl propanedione (PPD) containing product. Though the majority of light-curing dental materials are responsive in this range of wavelengths, it is suggested you should contact the filling material maker to make sure it before use.
Technical Data
Charging Base
AC Adapter Input: 100 – 240 VAC , 0.8 - 0.4 A , 47 – 63 Hz
OUTPUT: 12 VDC, 2.0 A
Charging box input: 12 VDC, 1 A
Fuse ration: 250V/2A
Charging box output: 8.4 VDC / 1.2A
Power indicator: Green LED
Charging indicator: Orange LED
Light intensity indicator: Blue LED
Dimensions (length/width/height): 150mm/90mm/60mm
Height with handpiece inserted: 180 mm
Weight: roughly 430 g
Handpiece
Power supply: Lithium battery – 7.4V DC, 2600 mAh
Wavelength range: 390 - 480 nm
Dimensions
Diameter: 50 mm
Length (with/without light guide): 185 / 125 mm
Height: 165 mm
Weight (with light guide and battery): Roughly 345 g
Charging Base and Handpiece
Time to charger empty battery: approximate 3 hrs
Relative humidity: max. 80% at 37℃ max. 50% at 40℃
Protection from electric shock: Type BF (IEC601-1)
Equipment class: Class II (IEC601-1)
Protection from ingress of liquids: None
Protection from ingress of AP/APG: None
Applied Part: Light Probe
Operation
Activating and Deactivating the Curing Light
1. Activate the Curing Light by pressing the power button.
2. If it is desired to turn off the Curing Light, this can be done by again pressing the power button.
3. Curing: the probe tip shall be used in close proximity to the material to be cured. Avoid actual contact. The flat end of probe should be parallel to the surface being treated.
4. Curing Light intensity settings:
a. High mode: at constant intensity 1,900m W/cm2 - 2,000 mW/cm2
b. Soft start: initially 35 - 50% energy of high intensity and then switch to high intensity
c. Low mode: at constant 35 - 50% energy of high intensity
d. Continuous mode: at a continuous on/off cycle of high intensity 2,000 mW/cm2
5. Curing time: High mode with different curing time: 1 sec to 5sec available
Low mode with 2 different curing time available: 5sec 10sec
Soft Start with 2 different curing time available: 7sec 12sec
Continuous mode with 16 cycles each of 1 sec, 2sec, 3sec; 1 second interval.
6. Total working time with new fully charged battery: approximate 30 minutes.
7. If the temperature on the handpiece is over 50℃, the overheat symbol will show up and the buzzer will beeps 5 short tone. Curing Light will not be activated until device temperature lower than 50℃.
8. If the battery voltage gets too low, the battery capacity column will run out and the buzzer will beep 3 short tone. Please replace with another fully charged battery and place the empty battery into charging base for recharging.
9. Rotate the light guide into the optimal position for polymerization.
10 Place the Accessories light guide as close as possible to the filling material.
Avoid directly contacting the filling material!
a. Keep the light guide clean at all times to obtain optimal light output.
b. Damaged light guide must be replaced immediately, since damaged light guide may reduce light intensity or injures the patient.
11. When curing process is finished, always place the Curing Light back to holder.
#Accessories #Curing Light #Gun-Type Curing Light
Video
Chungli, Taoyuan, China Taiwan
Send your inquiry to this supplier