With stable and high working performances low maintenance costs hot popular high effiency wood chips hammer mill for sale
With stable and high working performances low maintenance costs hot popular high effiency wood chips hammer mill for sale
With stable and high working performances low maintenance costs hot popular high effiency wood chips hammer mill for sale
With stable and high working performances low maintenance costs hot popular high effiency wood chips hammer mill for sale

1 / 2

With stable and high working performances low maintenance costs hot popular high effiency wood chips hammer mill for sale

Get Latest Price
Send Inquiry
Model No. : MFSP-Series
Brand Name : TN-ORIENT

Product description

A) This   With stable and high working performances low maintenance costs hot popular high effiency wood chips hammer mill for sale          should be fixed installed. And the belt wheel of crusher should be parallel with the belt of motor.  The two drive pulley trough should be in a straight line. Otherwise, it will not only accelerate the mechanical damage, but also easy to drop belts.  B) With stable and high working performances low maintenance costs hot popular high effiency wood chips hammer mill for sale      , If need to modify belt wheel, you must calculate the data which can satisfy the requirements of rotation speed of main shaft for the crusher.  Don’t allow to increase the rotation speed of main shaft arbitrarily. When the rotation speed is more 15% than rating data, it will make the machine severely shake. C) For   With stable and high working performances low maintenance costs hot popular high effiency wood chips hammer mill for sale         iron pieces, stone, etc entering the machine. D) Before use the   With stable and high working performances low maintenance costs hot popular high effiency wood chips hammer mill for sale , you should open the shell of crusher to check whether there is something wrong with the parts,  especially check the cotter on the rotor whether it is intact and whether it is loose. After confirm it is intact, shut off the shell tightly and tighten the hand wheel on the door.  Drive belts by hand to check whether there is something loose and whether there is any abnormal sound and phenomenon Collision phenomenon, etc. E) When start the machine, let it idle for 2-3 minutes without any material. After it normally work, then gradually feeding. F)     With stable and high working performances low maintenance costs hot popular high effiency wood chips hammer mill for sale    Operators should tightly enclosed cuff, wear masks. Prohibit wearing glove when work. When feed the raw materials,  operators should stand by side of the machine to prevent materials rebounding to hurt people. When crush long straw,  don’t tightly grasp it to prevent materials rebounding to hurt people. G) When feed materials to the machine, you should feed it equally and gradually increase the quantity until it normally works. H) If materials block the hopper, don’t allow using wood and iron sticks or hand to poke them which can prevent sticks entering into machine or hurt people.  Please use hard straw to poke the materials into crusher. I) Pay attention to the operation situation. If find the machine is shake or there is some abnormal sound or there some materials rebound,  turn off the machine to check where is wrong.  When check and mend the machine, you must turn off the machine. J) Prohibit opening the door of crusher when it works. You should add protection guard on the belt driving.  Prohibit overloading work for long time. Prohibit putting tools on the crusher or materials to prevent falling in the machine.  Prohibit smoking at work area. Pay attention to waterproof and moisture-proof. K) The length of powder packing bags should be more than 1.5. The packing bag should have good breathability. L) Before turn off the machine, stop to feed materials first. After all of materials come out and then turn off the machine. After work, clean and lubricate the machine.  IV. Operation and Maintenance.   (A) There is one piece of board under the hopper. You can adjust the size of board to control feed quantity.  Through control feed quantity can increase the efficiency and powder quality.   (B) The crusher has different size of sieves. You can choose different size of sieves to get different size of powder. When install sieve,  you should choose the proper connection mode of the sieve joints according to the rotation direction of rotor.  Make sure the direction of inner side of joint is the same as rotation direction. If pores of sieve is coned,  because there is little burr on the edge of holes, therefore, please use the sides of large hole outside to install which is convenient for installation. C) The crusher which is installed with wind pump can adjust the size of wind to control the crush powder.   V. Security Technology  (A) This crusher complies with national standard. (B) All of components should be tightly fastened to guarantee that they can be loose when the machine vibrates. (C) Protection device. The driving parts which are exposed must add protection device. The size of sieve holes should guarantee that any part of people can’t touch it. The protection device should have enough hardness which can guarantee that when people touch it without any distortion or displacement. (D) Feed inlet. (1) When the materials are Green and Coarse Fodder (grass, other aquatic plants, wheat straw, corn stalks, potato vine, and other types of straw, rattan),  the length of of hopper for Crusher should be more than 500 mm. The height of flat roof for hopper should be between 700 mm-1100mm.  (2) When the materials are cereals (wheat, soybeans, corn, sorghum, etc), the crusher should install a hopper which can control the capacity.  (3) The crusher which is automatically feeding must match protection equipment which can prevent the magnetic metal feeding into the crusher. (4) There must be a warning sign on the hopper of the crusher which should be feeded by hand. (F) This crusher has installed a lock system, when open the door of crusher or the door is not closed properly, the motor can not start. VI. Operation requirements (A) The workplace for crusher should be spacious, ventilated and enough space. And the workspace should match fir fighting equipments. (B) Before start the machine, please adjust and maintain it according to operation manuals. And check whether the tightening parts are fastened.  Under guarantee the safety of people and machine, you can start the machine. After 2-3 minutes idle operation,then you can feed materials. Before feeding,the suction system should normally work. (C) When the machine works, if there is abnormal noises, you should turn off the machine immediately. Prohibit to mend the problems,when the machine works. (D) After work, the machine should be idle for 2-3 minutes. When the materials in the machine all come out, you can turn off the machine. VII. Weared parts.

Name 

Type

Quantity

Remark

Triangle adhesive tape

GB1171-74

3

B-2240

Bearings

GB281-64

2

312

Hammers

 

16-56

 

Screen

 

4

 

VIII. Problems and solution.

Problems

Reasons

Solution

This crusher is consumingly vibrating with large noise.

The arrangement of hammers is not proper.

Adjust the arrangement of hammers.

There is large difference of weight between the two counterparts Hammers.

Change the hammers which there are difference weight less than 5 gram.

The seat of bearing for main shaft is loose.

Fasten the screws.

The bearing for main shaft is broken.

Change new bearings.

Some harmmers are blocked.

Adjust the hammers.

             
Send Inquiry

Product Alert

Subscribe to your interested keywords. We will send freely the latest and hottest products to your Inbox. Don't miss any trade information.

版权所有 © 宁波全贸信息技术有限公司 浙ICP备12012821号-1 浙B2-20200628