SR201 Two-way electronic valve /electronic water valve

Product Description SR201 Two-way electronic valve /electronic water valve Product description:   SR201 electric two-way valve is used in controlling the cold or hot water pipe on or off in air conditioning system, for the purpose of controlling room temperature. valve is driven by hysteresis synchronous motor, returned by spring. When the valve does not work, it’s in normally closed state, when it works, A opening signal is provided by thermostat, to make the electric valve connect AC power and become opening state, cold water or hot water flows into the fan coil, to provide cool air or hot air for room; once the room temperature reaches the setting point of thermostat, the thermostat will shut down the power of electric valve and the spring will return to make the valve closed, thus cutting off the flow of water into the fan coil. As the valve closed or open, room temperature is always maintained at the thermostat setting temperature range. SR201 series has two forms : two-way normally closed valve and three-way split valve, the sizes of valve threads are DN15, DN20, DN25 three type. SR201 electric valve’s actuator and valve itself are installed by slip-on connection, So, the actuator can be installed after the valve is installed.      Features: Forged brass body Stainless steel seat, aluminum casing Fully enclosed hysteresis synchronous motor, stainless steel spring Body Connection thread: British standard flat thread (female thread) BSPP North America used pipe thread (female thread) NPT Motor power, low noise, light weight, easy to use, at the rated voltage frequency of the motor speed is not affected, Remains constant, if the motor overload or stall, the motor coil will not burn actuator and valve itself are installed by slip-on connection, which can be quickly and easily disassembled without any tools, so it’s easy to install and use   Technical Parameters: Valve size: DN15, DN20, DN25 Connection: threaded connection Valve structure: two-way, three-way Media: hot / cold water Pressure: PN20 Close differential pressure: 0.18 ~ 0.22Mpa Power supply voltage: AC220V ± 10%, 50 / 60HZ consumable power: <6.5W Run mode: On or Off Valve action time: Opening time: ≤18S Closing Time: ≤7S     Model and size    

model	Size (mm)
	A	B	C
DN15 two-way valve	70	23	86
DN15 three-way valve	70	33	86
DN20 two-way valve	79	23	90
DN20 three-way valve	79	34	90
DN25 two-way valve	88	23	95
DN25 three-way valve	88	42	95

  Specification

Model	Flow Coefficient(KV)	Thread	Differential pressure	Medium	Medium Temp	Ambient Temp	PN	power
DN15 two-way valve	2.2(2.5)	1/2’’	0.22	Water/ Hot water	0-94℃	0-40℃	2.0	AC 24V AC 110V AC 220V 50/60Hz
DN15 three-way valve	2.6(3.0)	1/2’’	0.22
DN20 two-way valve	3.0(3.5)	3/4’’	0.20
DN20 three-way valve	3.4(4.0)	3/4’’	0.20
DN25 two-way valve	6.9(8.0)	1’’	0.18
DN25 three-way valve	6.5(7.5)	1’’	0.18

  CERTIFICATION: ISO, TS, API, GOST, CE....etc  We pay much attention in Test process: (1) Shell Hydrostatic Test

ANSI B 16.34 Section 7.1
Valve Size NPS		Test pressure				Test Time. Sce
Below DN50		1:5 times the 100°F				15 Sce
DN65~DN200		Rating of  ANSI  Class				60 Sce
Up DN250		Max. Operating Pressure				180 Sce
		Test pressure should be above 1.5 times  than the valve's Max work pressure (100F)

(2) Seal Hydrostatic Test The pressure should be more 1.1 times than working pressure by seal hydrastatic test  

ANSI B 16.34 Section 7.2
Valve Size NPS		Test pressure				Test Time. Sce
below DN50		1:1 times the 100°F				15 Sce
DN65~DN200		Rating of  ANSI  Class				30 Sce
above DN250		Max. Operating Pressure				60 Sce
		Test pressure should be more 1.5 times  than the valve's Max work pressure (100F)				180Sce

(3) Seal Air Test Seal air leakage test is based on 80PSIG(6kgf/cm2) inert-gas or the air reach the test pressure, then close the valve. after that check the valve whether it is leakage or not.     Packaging & Shipping     Our Services   1.100% factory price, because we are direct producer of ball valve, butterfly valves, check/non-return valves, gate valves and so on. 2.Market, technical support and after-sale service within 24 hours. 3. You can order your own configuration. A: Manual     B: pneumatic   C: electric   D: bare shaft  E: disc with pin    F: disc without pin   G: double half shaft   H: one piece body   I: two pieces body  J: logo    Company Information     Fully welded ball valve - Company advantages: 1. We are factory:  We have strict quality control system and amounts of testing equipments for different kind of valve, such as size, pressure, working environment etc. also can provide the competitive price.   2. Certification: API, CE, ISO,GOST, TS ..etc 3. Low MOQ:  Our factory owns the casting company by itself. We are always ready for providing the sample and producing some small orders, in order to meet the business well. 4. OEM Accepted: We can make the products with the client's demand standard or the customer requirement. 5. Complete Service: We are always ready to hear from you, reply within 12 hours. 6. Quick Delivery: We always keep the large stock for some hot products.   FAQ   1.What's payment terms?   30% payment in advance, 70% balanced before delivery.  (if total value is USD$ 500, we suggest 100% payment in advanve.) 2.What's MOQ?   One set.    (if small size, we can check if free sample or not, freight need to be paid by customer.) 3.How control the quality of ball valve? Select high quality raw material; Strict required during machining; Seat material comply with food grade; Tested twice to insure zero leakage; First copper plating disc, then nickle plating disc to increase the adhesiveness 4.Delivery time? 10-15 days after received the advance payment.  (if stock, about 10 days)