polymeric carbon fiber vinyl with bubble free

Specifications polymeric carbon fiber vinyl with bubble free

1)thickness : 0.17mm

2)quality : top item with bubble free

3)adhesive : remove

Polymeric carbon fiber vinyl with bubble free,vinyl sticker,3D sticker Advantages Osign brand Carbon Fiber Vinyl are flexible PVC films with perfect adhesive intended  to cover all type of  the  surfaces, such as wall covering, furniture, fixture, ceiling, doors, elevators,  exterior/interior applications.   Osign brand Carbon Fiber Vinyl are durable, dimensionally stable, vinyl films that were specifically developed for interior/exterior decorations and refurbishment.     Effective Performance Life The warranty for Osign brand Carbon Fiber Vinyl for interior/exterior decoration as stated here extend to automotive or personal vehicle applications .The warranty applies to films that are exposed interior/exterior at a vertical angle (defined as +/-10°). A significant decrease in durability may be experienced if films are exposed other than vertically. Such non-vertical application should be based on Osign tests results and approval to determine acceptability. Effective Performance Life of unprinted interior/exterior Osign brand Carbon Fiber Vinyl depends on application exposure zones as follows.   Fabrication Cutting with Electronic Systems Osign Carbon Fiber Vinyl is normally applied in sheets directly from the roll. In case people want to cut or screen print that is possible but not the primary intention of the film. Knife adjustment may be required as the product construction may differ from comparable products. The minimum height for text is 10 mm.     Physical and Chemical Properties Values given are typical and are not for use in specifications. If a custom specification is desired, a request should be submitted through your sales representative. The following data is given for unprinted film. Application Temperature We recommends applying Carbon Fiber Vinyl products at 15°C - 38°C.   Physical Properties

Property	Metric Units
Thickness (Film + Adhesive)	0.170mm– 0.180 mm
Elongation	> 100 %
Dimensional Stability (X-gash)	> 0.3 mm max
Abrasion Resistance Taber abrasion (0.5 kg load, CS-17)	1000 cycles Surface will be damaged
Impact Resistance (Gardner at 0°C), 2 lb X 5 inch at 4°C	No effect
Humidity Resistance at 40°C (95% RH X 7 days)	No effect
Water Resistance (40°C water X 7 days)	No effect
Stain Resistance 18 hours Milk, Coffee, Wine, Lemon juice, Tea, Vinegar, Soybean oil, Salt water (1%), Ammonium water, Soap water (1%), Synthetic detergent, Hydrochloric acid (10%), Sodium hydroxide (10%)	No effect

    Adhesion (N/25 mm)

Substrate	Adhesion (No Primer)	Adhesion (W/DP-900N)
Lauan Veneer	4.9	34.3
China Veneer	4.9	30.4
Plaster Board	-	4.9*
Asbestos Slate Board	4.9	34.3
Melamine-baked Steel Sheet	30.4	52
Phosphate-coated Steel Sheet	24.5	54
PVC-coated Steel Sheet	44.1	44.1
Aluminum	27.1	39
Stainless Steel Sheet	37.2	42
Acrylic Board	38.2	54.9
Mortar	3.9	21.6

  Chemical Resistance Product applied to an aluminum panel, conditioned for 72 hours and then immersed in the chemical agents.     Stain Resistance Carbon Fiber Vinyl product applied to an aluminum panel and placed in direct contact with the following substances at 20°C, 65%RH.     Flammability Information about the new Carbon Fiber Vinyl approval numbers according to various test standards  

Approval Type, Number	Product Type	Test Substrate	Classification	Copy of Certificate
IMO	FW 646	Non-flammable substrate	Non-combustible	GPRD
SBI   EN 13823:2002	ST 553	Non-flammable substrate	B-s2,do	GPRD
DIN 4102-1	Product Group 1-10 (all DI-NOC films)	Non-flammable substrate	B1	GPRD
DIN 54837	PS, WG	Non-flammable substrate	Non-combustible	GPRD
FAR-25.853	WG 165	Non-flammable substrate	Non-combustible	GPRD

    Cleaning/Maintenance For cleaning of applied Carbon Fiber Vinyl use a soft textile with detergent and water. For heavy dirt accumulation use detergent and water at 70°C - 80°C.   Removal Carbon Fiber Vinyl are removable with a heat gun at 80°C – 100°C or the Bosch steam remover PTL1 can be used.     Shelf Life, Storage, Shipping The fabricator may store unprinted film for a period of up to three years. Film and markings must be stored in a clean area, free from excessive moisture and direct sunlight, on at least a 3" core with the film facing outward, with ambient temperatures of 35°C or less.