Specifications 1. buffer tank may add to the line
2.condensator may add to the line
3.vacuum pump can add to the line
4.stevioside dry
This unit can be widely used for drying or mixing powdergranule materials in pharmaceutical, chemical, foodstuff industries etc. It is especially suitable for following materials: Heat sensitive materials Materials that is easy to oxidize and have dangerous Materials that solvent and toxic gases are need to recove Materials that have special requirement of crystal form. Materials that have special requirement for the content of residual volatile.
Model | 100 | 350 | 500 | 750 | 1000 | 1500 | 2000 | 3500 | 4500 | 5000 |
Volume inside the tank(L) | 100 | 350 | 500 | 750 | 1000 | 1500 | 2000 | 3500 | 4500 | 5000 |
Loading capacity(L) | ≤50 | ≤175 | ≤250 | ≤375 | ≤500 | ≤750 | ≤1000 | ≤1750 | ≤2250 | ≤2500 |
Revolution(rpm) | 3-13 | 6 | 5 | 4 | 4 | 4 |
Power of motor(kw) | 0.75 | 1.1 | 1.5 | 2.2 | 3 | 4 | 5.5 | 7.5 | 11 | 15 |
Occupied area L×W | 2160*800 | 2160*800 | 2350*800 | 2560*1000 | 2860*1300 | 3060*1300 | 3260*1400 | 3760*1800 | 3960*2000 | 4400*2500 |
Rotating height (mm) | 1750 | 2100 | 2250 | 2490 | 2800 | 2940 | 2990 | 3490 | 4100 | 4200 |
Design pressure inside the tank(Mpa) | -0.1-0.15 |
Design pressure of jacket (Mpa) | ≤0.3 Mpa |
Working temperature() | (85 in the tank ≤85) tank≤140(in the tank ≤140) |
When condenser is used, model and power of vacuum pump | 2X-15A 2KW | 2X-15A 2KW | 2X-30A 3KW | 2X-30A 3KW | 2X-70A 5.5KW | JZJX300-87KW | JZJX300-49.5KW | JZJX600-811KW | JZJX600-420.5KW | JZJX600-422KW |
When condenser is not used, model and power of vacuum pump | SK-0.41.5KW | SK-0.41.5KW | SK-0.82.2KW | SK-2.7B4KW | SK-2.7B4KW | SK-35.5KW | SK-611KW | SK-611KW | SK-915KW | SK-1018.5KW |
Weight (kg) | 800 | 1100 | 1200 | 1500 | 2800 | 3300 | 3600 | 6400 | 7500 | 8600 |
| | | | | | | | | | | |
NOTES: For raw material, if its volume has great change before and after dryer,then its filling confficient may be increase or decreased suitablely. Speed adjusting motor of 0-6rpm might be chosen according to the users requirements. The follong aspects should be point out when to order: 1, The above mentioned parameters are calculated based on material density of 0.6g/cm3 . If its over please point out. 2, If certificate for pressure vessel is required, please point out. 3, If glass lining for interior surface is required, please point out. If the material is explosive , or flammable, the calculation should be made according to trial results.
NOTE: 1 Its heating has three ways i.e. steam, hot water, heat conduction oil.
2When order, please indicate the temperature of raw material to be undertaken or the operation temperature of drier in order to choose or provide suitable heat source for you.
3When dry viscous raw materiel. our factory will design special stirring device in the chamber
4The auxiliary parts of vacuum drying system can be supplied and installed by Our factory, Please indicate them when order
5lf having special requirements, our factory can also design, manufacture and install as request.
6The cost of complete equipment should be increased in accordance with the needs.