Multi Output Current Low Voltage Dimmable 30W LED Driver 1

Multi Output Current Dimmable 30W LED Driver 1 - 10V For LED Tube

Description:

1, Low stand-by power, less than 0.5W.

2, Quick install design for side cover can save more installation cost. Thanks to press-in type input and output terminals, it is very easy to assemble.

3, Long shape housing design makes it easy to go through small cut hole.

4, Output voltage starts from 3Vdc, wide range output can driver min. 1pcs LED.

5, Multi-output current and voltage is suitable for different LED lights. Output current from 250mA to 700mA can be selected by DIP switches.

6, Jumper design for switching different dimming modes, it is very convenient to select suitable dimming function as you required.

7, Three types of dimming mode, PUSH in primary, PUSH dimming in secondary and 1-10V dimming. You can select dimming modes per jumper

8, Memory function: The driver has built-in permanent memory against power failure. Lights can return to previous dimming level when switch off and on again, even at mains restores.

9, Synchronization: thanks to the MCU programme, up to 50pcs drivers should be controlled by the same switch. This means there is no need for any additional synchrony wire in larger installations, where many drivers should be controlled by one switch.

10, Maximum length of the cable, from switch to last driver is 20m.

11, Factory setting: 100% dimming level and 250mA output.

12, Reset the LED diver easily by a jumper.

13, Protection: Short circuit / Over voltage / Over temperature.

14, 5 years guaranty

Applications:

For LED down light, LED panel light, led strip, led tube etc…

Dimming Operation:

A) PUSH Dim

Short push (<0.1sec): Ignore, to avoid reaction on AC spike.

Short push (0.1~1sec): Switch on or switch off.

Long push (>1sec): Dimming up or down, dimming level automatically stops at minimum or maximum value.

B) 1-10V Dim

Using the push dimming will make 1-10V dimming inactivated. The driver has to be reset to active the 1-10V dimming function again.

Synchronization:

For the resynchronization to work correctly when more than one driver is connected to the same push button, follow steps of below after the drivers are connected:

A) Press push button for more than one second, followed by a short push (<1s), now, led light switches off.

B) Do a long push, the system will be resynchronized.

Specifications

INPUT	Input voltage	220-240Vac
	Input frequency	50-60Hz
	Input current	0.16A max
	Power factor	≥0.90
	Efficiency(Note1)	≥85%
	Leakage current	＜0.5mA/240Vac
OUTPUT	Output current/voltage and load	250mA 3-60V DC 15W max 350mA 3-60V DC 21W max 500mA 3-58V DC 29W max 550mA 3-55V DC 30W max 600mA 3-50V DC 30W max 700mA 3-43V DC 30W max
	Output load range	1x30W max
	Current accuracy	±5%
	Dimming mode	1-10V, PUSH
ENVIRONMENT	Working temp.(Ta)	-20~50℃
	Surface temp.(Tc)	85℃max
	Working humidity	20~90%RH non-condensing
	Storage temp.	-40~80℃
	Life time	≥50,000hours
PROTECTION	Isolation class	Class II, SELV
	Protection class	IP20
	Short circuit	Protection type; auto rest
	Over voltage	Protection type; auto rest
	Over temperature	Protection type; auto rest
SAFETY&EMC	Safety	EN61347-1, EN61347-2-13, EN60598-1, EN60598-2-6
	EMC	EN55015, EN61000-3-2ClassC
		EN61000-3-3, EN61547
	Approvals	SEMKO, CE
	Withstand voltage	IN-OUT:3.75KVAC/5mA/1min; IN-FG:1500VAC/5mA/1min
		OUT-FG:500VAC/5mA/1min
NOTE	1, Efficiency is measured at 550mA/55Vdc output set by DIP switch 2, All parameters not specially mentioned are measured at 230Vac input, rated load and 25℃ of ambient temp.