F300 Automotive analog 0-5v digital rs232 rs485 Infrared sensor made in China with high accuracy

F300 Automotive analog 0-5v digital rs232 rs485  infrared sensor made in China   with high accuracy    Product Description               1 Overview
High resolution capacity fuel level sensor,RS232 interface, protocol support zero/full calibration.For this level sensor,we accept customize,the longest length is about 3000mm. 2 Specification Length 10-1000mm
Resolution 0.01mm
Pressure -0.1MPa~0.1MPa
Ambient temperature -40~70 o C
Sensor temperature -100~150oC
Sensor diameter 16mm
Output Analog Voltage:0-5V , or Digital: RS 232/485
Voltage DC 12~40V
Explosion-proof EXia II C T6
Mounting Flange
Media Diesel   3 Features
Fuel level detection for truck and non-road vehicle,
COM port or Analog voltage output;
High resolution and internl filter for fluctuation;
RS232 protocol support zero/full calibration.
4 Connection Diagram
4.1 RS232 model
Red Line: 24V+,
Black Line: GND
Blue Line: RXD
Yellow Line: TXD
4.2 0-5V analog model
Red Line: +12/24V,
Black Line: GND
Blue Line: 0-5V output   5.Application This is level sensor to detect fluid level on container, such as fuel tank, gasoline pump, fuel storage, water pool and etc.   6.Level Monitoring Our level sensor can accurately measure for you the volume of the liquid.Please refer to the following diagram.   The following diagram shows the comsumption of fuel with its speed,for fuel level monitoring.This level sensor can be used together with vehicle gps tracker.         7.Calibrator       User can cut short to specific length based on their requirement. After cutting short, please do belowcalibration.
It is recommend to do calibration while installation.
1.Adjustment of Zero
Push zero adjustment button for more than 5 seconds, the red led will light. After more than 5 seconds,push the zero button and keep pressed for more than 2s. The red led will be off. And zero adjustment done.
2.Adjustment of Full
Push full adjustment button for more than 5 seconds, the green led will light. After more than 5
seconds, push the full button and keep pressed for more than 2s. The green led will be off. And full adjustment done.     Installation Infrared sensor made in China If replace original sensor on vehicle, please firstly take off the original sensor, then go to next step. If install new sensor, directly go to next step.   1.Preparation Please check whether the sensor, accessories and tools are ready, including flange, rubber seal, O ring,screw(customer prepare), electric drill (customer prepare).
2.Drilling Holes
According to flange size, use electric drill to work out holes for sensor and screws.     3 Flange mounting Put O ring at bottom of sensor, then connect with flange and fasten.   4 Sensor mounting Put rubber seal on fuel tank, mount sensor, then fasten screws   5 Connect lines According to above 4 Connecting Diagram,Connect sensor lines with the device or equipment             FAQ   Infrared sensor made in China  1. Can I use it with gps tracker? Yes, it support any gps tracker with 0-5V analogue input or RS232 input. If RS232 interface, the gps tracker need to do integration with our sensor protocol.   2. Which is the gps tracker list it support? Any gps tracker with 0-5V analogue input and RS232 input. such as A300, VT310, MVT400, MVT600 and etc.   3. What is the resolution? 0.1mm. If multiple with section area, we can conclude the liter resolution, normally less than 1 liter for vehicle tank.   4. Can we measure the liter changing with it? Yes, create one map between level and liter, then can draw liter changing.   5. Why is it expensive than other floating sensor? Because capacitance is more stable and higher resolution than floating sensor. So do not compare with different type of sensor. Just compare with other capacitance sensor, our will be the most cost-effective one.   6. Do you have support for integration with our application? Yes, we have EE and SW engineers team to support for you with integration of our product.   7. Is it safe for using with gasoline? Sure, we have ExtdIIT certification.   8. Can we cut short to adopt our tank? No, it does not support user cutting short. We have another model F330 support customer resizing.   Packaging & Shipping Infrared sensor made in China We provide standard,strong,protective package for our products to prevent it from outer damage. For detailed information,please refer to the pictures attached below.       We provide many kinds of economic and express shipping method for your selection.         Company Information   We are Beijing Dingtek Technical Co.,Ltd.We especially engaged in personal gps tracker,vehicle/automotive gps tracker,liquid level sensors,industrial all in one pc.We have been in this line for many years.We provide competitive quality products and powerful customer service,and has receive high reputation from customers all over the world. Welcome to contact us for cooperation.      We provide most convincing products,solutions&services for our customers.       We have brances in Qingdao and Hongkong. Contact Information The following is my contact information,if you have any questions,please contact me:)   Look for cooperations with you!   Our Services